Mobile machines & lifting technology

In lifting technology as well as in mobile machines, the monitoring of the movement or position is required for functional and safety aspects. Micro-Epsilon sensors are used in numerous measurement tasks to ensure a controlled sequence of movement.

Displacement detection of hydraulic diving platforms

Draw-wire sensors from Micro-Epsilon ensure that the towers are in the exact position, which is why the height is measured precisely. This is the only way to easily control this between 0.8 m and 3.5 m ...

Показать детали

Synchronization monitoring with draw-wire sensors in telescopic platforms

For electronic synchronization monitoring, a draw-wire sensor is used here. These are easy to integrate, very compact and offer high accuracy in addition to the large measuring range. For displacement ...

Показать детали

Lift height of a catering vehicle

Catering vehicles play an important role in passenger air traffic. They are responsible for there being enough foodstuffs on board. It is especially difficult with the Airbus A380 to reach the loading ...

Показать детали

Synchronised lifting system lift height

Mobile lifting jacks are being used more and more often for commercial and railed vehicles. The lifting jacks for commercial vehicles are often designed as column lifts. In contrast, railed vehicles are ...

Показать детали

Wear measurement in the bearing

In modern marine diesel engines, the crankshaft bearing is subject to regular maintenance intervals. For predictive maintenance, inductive sensors (eddy current sensors) are used to permanently monitor ...

Показать детали

Piston position in the hydraulic cylinder

In modern hydraulic cylinders, the piston position is detected continuously. Therefore, inductive long-stroke sensors from Micro-Epsilon are used which are directly integrated in the hydraulic cylinder. ...

Показать детали

Position detection of the piston in the hydraulic cylinder

In order to detect the piston position of hydraulic cylinders, magnetostrictive and inductive sensors are directly integrated in the sensor. Therefore, the magneto-inductive sensor mainSENSOR is an alternative. ...

Показать детали

Jib lengths of mobile cranes

The current jib length is important when calculating the torque of the load on the crane. This length is measured with an integrated draw-wire sensor. This simple and telescopic measuring principle makes ...

Показать детали

Gap analysis in axial piston pumps

So far, gap measurements inside the pumps were not possible because of the extreme requirements. The sensors must be resistant to high speeds, high pressures up to 1,000 bar and temperatures above 100 ...

Показать детали

Lift platform – lift height

Side supports against tipping over are installed for lift trucks and lift work platforms. The crane or the platform can only be put into operation when the supports are completely extended so that there ...

Показать детали

Monitoring free-standing structures

High, free-standing structures such as cranes are monitored using inclination sensors which provide early warnings of a possible tip over in order to avoid accidents.

Показать детали

Measurement of track position errors

In rail transport, the new construction and reconstruction of track sections is subject to ever increasing requirements. A faultless track geometry is essential, especially for high-speed lines. In ...

Показать детали

Positioning of suction pipes for suction dredgers

Suction dredgers are seagoing vessels that collect sand and silt from the seabed in order to transport it over long distances. They are used for the construction and maintenance of ports and waterways ...

Показать детали

Precision synchronized lifting system

Synchronized lifting systems enable the raising and lowering of heavy loads controlled for distance and force or the controlled forward feed of large components. To achieve this, eight or more cylinders ...

Показать детали

Displacement measurement on slag transporter

Draw-wire sensors are used to reduce the standstill time of slag transporters during the loading and unloading. They are installed on the tipping cylinder and the support cylinder. In this way, the signal ...

Показать детали

Rack control unit - lift height

The frequently used automatic rack control units make modern warehousing much easier. These units must automatically travel long distances and position the products with millimetre precision at the end. ...

Показать детали

Crane support distance

A truck-mounted crane is frequently the better solution in many cases where loads have to be lifted. As a mobile solution, safety also plays an important role here. Therefore a load torque limiter controls ...

Показать детали

Forklift lifting height

A large part of internal transportation is performed by forklifts. The risk of tipping the forklift when products are lifted is high. Therefore, the permitted speed has been restricted with limit switches. ...

Показать детали

Sensorica-M, Ltd.
443030 Samara
ul. Mechnikova 1, of.203
info@sensorica-m.ru
+7 / 846 / 24 65 213
+7 / 846 / 33 45 517